Looking for:
Ge designer series 4-device universal remote manual |
GE Universal Remote Manuals.Ge designer series 4-device universal remote manual
The following is a short tutorial on programming most models of GE universal remotes with 4 digit codes. See also this page for general GE remote code entering instructions. The indicator light will blink, then stays lit. Step 3: Enter the 4 digit code for your device. After a valid code entry, the indicator light turns off. For an invalid code, the indicator light flashes. If the device responds, no further programming is required.
If some buttons don't work as they should, try a different code listed for your brand. To find out the version your remote uses, open the battery compartment, remove the batteries and locate the sticker containing the model number. A Version 2 through Version 5 remote will have a "V2" to "V5" after the model number. Older remotes with no version after the model use the V1 code list. In order to save you the hassle of going through multiple code tables, we have compiled together the code lists from different versions of GE remotes sharing the same code base e.
If your remote is slightly old, you'll get the benefit of finding the code for your device even if it appeared after your remote was manufactured, but uses an old code that already exists preprogrammed in your model.
You can also find the code for some old devices that are dropped from the code lists, but still supported by newer remote controls. The only downside of this approach is, that there will be a few codes that are only supported by a particular version.
So, if a code listed for your brand is not supported by your remote, try the next one from the list. Sometimes a code will be accepted, but only allow limited function control e. In this case, continue programming using the next code for that brand. The Auto Code Search searches automatically through all of the codes stored in your remote. If your device does not respond to any of the codes listed for your device, or your brand does not appear in the code lists, try the following steps:.
The indicator light will blink once and then remain on. Wait patiently until the remote sends a batch of 10 codes to the device. The indicator light will blink once for each code and remain on after sending the 10 codes. Repeat this step again and again until your device turns off. The remote will resend the last 10 codes one by one. Step 7: When the device turns off, press and release the same device button you pressed in Step 3 to store the code. Step 2: Press and hold the "SETUP" button until the red indicator light stays on around 4 seconds and then release the button.
The red indicator will blink once and remains on. The red indicator will flash approximately every 2 seconds as the remote searches. The remote must be pointed at your device for the entire duration of this search. Step 5: Place your finger on the 1 button so you are prepared to lock-in the code.
Step 6: When the device shuts off or begins playing, press the 1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code. Step 7: Point the remote at your device and check to see if the remote operates it as desired. If it does, no further programming is required. If it does not, return to step 2 and start the auto search again.
The red indicator will blink once, then stays on. The red indicator will blink with each keypress. When all codes have been searched the red indicator flashes rapidly for 3 seconds. The indicator light goes off. Then follow the steps above for Code Search.
Ge designer series 4-device universal remote manual.GE 40081 4-Device Universal Remote Control User's Manual and Instructions
Hide thumbs. Table Of Contents. Quick Links. Table of Contents. Previous Page. Next Page. Page 3: Introduction Introduction Congratulations. Page 4: Button. ENTER may. Page 5 Button Functions, cont. Red Indicator:. MUTE: Turns. MENU: brings. RIGHT navigation. Page 6: Initial. Battery Saver Your. Code Saver You. Power-On Default The. Code Setup The. Page 7: Direct. TV, DVD,. Code TV. Page 8: Code. SETUP button.
ENTER to. DVD button,. CABLE in. ON-OFF instead.. Page 9: Code. TV button. Controlling Combo Devices Some. SETUP buttons DVD Mode,. Punch- Through. DVR Mode. Page Troubleshooting Troubleshooting Remote does not operate your product. Remote does not operate some features of your product. Red Indicator blinks after you program a product code. Page 14 90 Day Limited Warranty Jasco. Company Road Oklahoma. Page 16 Jasco. This manual is also suitable for: Print page 1 Print document 16 pages.
Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.
No comments:
Post a Comment